steering column

Before removing steering column switch , remove ignition key .

拆卸转向柱开关前，要先拆下点火钥匙。

Loosen lower steering column mount .

松开下转向柱支架。

The overdrive switch was on the steering column .

超速挡的开关在转向杆上。

Experiment study about the load bearing capacity of the steering column

转向柱管承载能力的试验研究

Cherishing Time Study on Steering Column Safety Performance while Car Crashing

基于车辆碰撞时转向柱安全性研究

Design of the New Type Energy Absorbing Steering Column Assembly of Minibus

微型客车新型吸能转向管柱总成设计

Failure Analysis of the Steering Column of Automobile

轿车转向柱总成故障原因分析

Position key cylinder into steering column as it would normally be in the ON position .

将钥匙柱放入转向柱中，其正常应该在ON（开启）位置。

Install lower part of steering column trim .

安装转向柱装饰件的下部。

Tube and ball type steering column

球轴承套管式转向管柱

Observe the tightening sequence of steering column at mounting bracket .

请遵循固定支架上转向柱的紧固顺序。

In cases where the steering column shows no external damage it can be difficult to detect damage .

万一转向柱指示看起来没有外部损坏，则检测其损坏会很费力。

Place ignition switch into openings on steering column .

放置点火开关至打开的转向柱上。

Collision Analysis of Steering Column on EPS

电动转向器中转向柱的碰撞性能分析

The cruise control switches are conventionally mounted on the steering column .

巡游控制开关按常规安装在转向轩上。

Steering Column Opening Cover Remove / Install

转向柱开口护盖的拆卸／安装

Remove the sealing bellows of the steering column .

拆下转向柱的密封防尘套。

Visible or perceptible damage to the steering column .

转向柱上有可见的或可检测到的损坏。

To remove and install the sealing bellows , the steering column must be removed .

要拆卸和安装密封防尘套，必须拆下转向柱。

Release steering column , disconnect steering column plug connection and let it hang down .

松开转向柱，断开转向柱插头，并将它挂起。

If the vehicle is so equipped , remove the tilt steering column lever .

如果车辆正是如此装配，拆去倾斜转向柱把手。

Remove the steering column carefully .

小心拆下转向柱。

If a new steering column was installed , the control unit must be taught using the PIWIS tester .

如果安装了新转向柱，则必须使用piwis检测仪设定控制单元。

To remove , loosen the clamp of the steering column switch from below .

从下面旋开转向柱开关的卡子，然后拆卸下来。

Install the steering column adjusting lever .

安装转向柱调整杆。

An internal high pressure forming process of a car steering column has been researched and the part is produced through experiments successfully .

研究了某型号轿车转向节臂零件的内高压成形工艺，并成功试制出样件。

In sport mode , paddles mounted on the steering column allow you to control gearing .

在运动模式下，你可以利用转向柱两侧的换档拨片控制档位。

Install steering column trim and airbag contact unit in the centre position , using the screws .

用螺钉安装转向柱装饰件和中间位置的气囊螺旋线圈。

Move the BCM towards the steering column far enough to access the three wire harness connectors .

向着转向柱移动BCM足够远以便能碰到三个线束接头。

Remove and disassemble steering column switch .

拆卸和拆解转向柱开关。